CR-10 | CR-10S | BondTech BMG + E3D V6 + EZABL Mount Assembly 模型预览

GrabCAD 模型信息

CR-10 | CR-10S | BondTech BMG + E3D V6 + EZABL Mount Assembly · 模型 393909

作者:MP23Racing

This new mount assembly was designed to restore full use of the CR-10/CR-10S build area. I was not thrilled with the previous design I made which eliminated almost 15-20 mm in X and Y so I went back to re-design this unit to fit as close to the stock CR-10 extruder assembly as possible to re-gain this area back. The Z-Axis will also improve as the long E3D hotend will be closer to the bottom of the X-Axis carriage as compared to the stock assembly. Only Parts/Hardware needed: Extruder mount screws for Bondtech assembly (should be included in kit) 6X M4x0.7mm x 22mm long screws for the blower fan mount and hotend cooling fan Noctua 40mm Fan (NF-A4x10 FLX) https://www.amazon.com/gp/product/B009NQLT0M/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 50mm x 15mm Blower Fans https://www.amazon.com/gp/product/B071WMHNG5/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1 EZABL Sensor https://www.th3dstudio.com/product/ezabl-kit-direct-wire/ Small Nema 17 Stepper Motor https://www.omc-stepperonline.com/hybrid-stepper-motor/nema-17-bipolar-18deg-18ncm-255ozin-07a-29v-42x42x25mm-4-wires-17hs10-0704s.html Assembly Instructions: Mount the Bondtech Extruder Carriage part to the CR-10 X-axis carriage first. Then install the blower fan, blower fan duct, and angle brace next using the two M4 screws. This will give more room to install these components without the stepper motor getting in the way. Last step is to install the stepper motor and BondTech extruder on the mount to complete the setup. Make sure to orient the heat block so that the nozzle is pointing closer to the front of the mount and thermistor/heater cartridge wires are exiting toward the bondtech assembly side. Notes: Suggested Materials (High Temp Resistant): PETG (Material I chose) Nylon ABS It is recommended to use rafts on both parts for this assembly. The dimensions are critical for these parts so preventing any warp while printing is required. I was able to successfully print the Extruder Carriage without supports anywhere, but I would suggest to add at least 4 top and bottom layers for the section that the stepper motor mounts for added rigidity and flatness. On the Blower Fan Mount, I used supports only under the first portion of the duct to ensure the remaining overhang layers would print correctly, but depending on layer height and speeds, the results could vary. Marlin Firmware Settings for ABL Sensor Position X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] Y_PROBE_OFFS...

格式
Rendering、STL、STEP / IGES
分类
3D printing、Tech
标签
e3d、v6、bondtech、bmg、mount、cr10、cr10s、noctua、40mm、fan
数据更新
2026-11-11T07:06:53Z
前往 GrabCAD 查看

CADSEEK 是第三方中文模型检索工具,与 GrabCAD 无隶属或官方合作关系。模型文件、许可与最终详情以 GrabCAD 原始页面为准。